Certifications and Specifications

ISO-9001 Certification

ISO-9001 Certificate

ASTM Test Methods

ASTM-D624-00 – Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
ASTM-D638-22 – Standard Test Method for Tensile Properties of Plastics
ASTM-D1238 – Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
ASTM-D1525 – Standard Test Method for Vicat Softening Temperature of Plastics
ASTM-D2000 – Standard Classification System for Rubber Products in Automotive Applications
ASTM-D2240 – Standard Test Method for Rubber Property—Durometer Hardness
ASTM-D4060 – Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser
ASTM-D4101 – Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM-D412 – Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers – Tension
ASTM-D4801 – Standard Specification for PE Sheeting greater than 0.010
ASTM-D5630 – Standard Test Method for Ash Content in Plastics
ASTM-D624 – Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
ASTM-D638 – Standard Test Method for Tensile Properties of Plastics
ASTM-D747 – Standard Test Method for Apparent Bending Modulus of plastics by means of a cantilever beam
ASTM-D790 – Standard Test Methods for Flexural Properties of Unreinforced and reinforced plastics and electrical insulating materials
ASTM-D792 – Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
SAEJ-1756 – Determination of Fogging Characteristics of Interior Automotive Materials

Fiat Chrysler Specifications

MS-AY 620 – Cellular Cross-Linked Polypropylene (XLPP)
MS-DB-500 – Plastics Thermoplastic Polypropylene (PP) All Automotive Grades
MS-DC 642 Plastics – Thermoplastics – Filled Polyethylene Sound Barrier Applications
MS-DC-242 – Thermoplastic Elastomeric Styrene Block Copolymer and Blends
MS-DC-259 – Thermoplastic Calendared Ethylene Vinyl Acetate (EVA) for Sound Barrier Applications
MS-DC-643 – Thermoplastic or Thermoset Rubber Floor Covering Materials

DIN ISO Test Methods

DIN EN ISO-1924-2 – Paper and Board – Determination of tensile strength properties Constant Rate of Elongation method

Federal Specifications

FMVSS-302 – Flammability of Interior Materials
SAE J-369 – Flammability of Polymeric Interior Materials – Horizontal Test Method

FINAT

FTM-10 – Quality of Silicone Coated Substrates for Self-Adhesive Laminates – Release Force
FTM-11 – Quality of Silicone Coated Substrates for Self-Adhesive Laminates – Subsequent adhesion
FTM-25 – Evaluation of the silicone coverage of coated papers use of a water-based stain test

Ford Specifications

ESA-M11P19-A – Adhesion Requirements Polyurethane Foam to Polypropylene Pressure Sensitive Film
ESA-M4D197-A – Polyethylene Copolymer Molding Compound
ESA-M4D197-A3 – Polyethylene Copolymer Molding Compound
ESA-M4D200-B – Polyurethane (PUR) Foam Flexible Restricted Flow
ESB-M4D145-A – Polyethylene (PE) Linear Blow Molding Compound
ESB-M4D157 – Polyethylene (PE) Sheet, Black
ESB-M4D308-A – Polypropylene High Impact Grade
ESB-M5G26-F – Barrier, Ethylene Vinyl Acetate, Moldable (Specific Gravity 2.1)
FLTM BO-040-01 – Short and Long Term Environmental Testing
WSB-M4D619-A1 and A2
WSD-M2D378-A1 – Thermoplastic Elastomer (TEO) – Polyolefin EPDM Rubber Modified Engine Coolant and Moderate Heat Resistant – 60-89 Durometer
WSD-M5G57-A – Barrier Acoustical, Ethylene Vinyl Acetate, Mineral Filled
WSK-M4D798-A – Polyethylene (PE) Low Density Flexible Molding Compound
WSS-M15P4-F – Assembly Performance Hard Mold In Color Interior Components
WSS-M2D476-A3 – Thermoplastic Polyolefin Elastomer (TEO) – 50% Minimum Recycled Content Hardness 60-90
WSS-M2D492-A1 – Styrene Butadiene Rubber (SBR) Extrusion and.or compression Molding, Post Consumer Recyclate
WSS-M2D505-A5 – Thermoplastic Elastomer Styrene Polyolefin Block Copolymer (TES) 90 Durometer A Hardness – Exterior Applications
WSS-M3H145-A – Carpet, Polyester Nonwoven Random Velour, Needled Latex Back coated 745gsm (22oz)
WSS-M4D729-B1 – Polypropylene (PP) Homopolymer 20% Mineral Filled Molding Compound
WSS-M4D729-B5 – Polypropylene (PP) Homopolymer 20% Mineral Filled Molding Compound
WSS-M4D729-B7 – Polypropylene (PP) Homopolymer 20% Mineral Filled Molding Compound, Underbody and Engine
WSS-M4D932-A1 – Polypropylene (PP) Copolymer Blow Molding Compound
WSS-M4D932-B1 & B2 – Polypropylene (PP) Copolymer, Medium Impact Compound, Blow Molded or Injection Molded, Under hood
WSS-M4D955-A – Polyethylene (PE) High Density Molding Compound
WSS-M4D955-B – Polyethylene (PE) High Density Molding Compound Non-Visible Exterior Underbody
WSS-M5G52-B – Barrier, Acoustical
WSS-M8P16-B – Performance Carpet Floor and Trim
WSS-M99D63-A3 – Thermoplastic Elastomer Floor Covering, Grained Shaped
WSS-M99D67-B1 – Floor Mats, Flat Polymeric Grained Shaped with or without deep lip tray
WSS-M99P2222-C1 C2 C3 C4 – Performance Vehicle Interior Environment Quality Component Requirements, Allergy testing and Direct Skin Contact, HVAC Requirements
WSS-M99P32-A – Performance Acoustical and Thermal Assemblies.txt
WSS-M99P32-C – Performance Acoustical and Thermal Assemblies
WSS-M99P32-D1 – Performance Acoustical and Insulators Interior Assemblies
WSS-M99P32-E1 – Performance Acoustical and Insulators Interior Assemblies
WSS-M99P32-E6 – Performance Acoustical and Thermal Components and Assemblies for Engine, Under hood, and Tunnel Applications
WSS-M9P11-A – Throw in Mat Assemblies Performance Elastomeric, All weather

General Motors Specifications

GM-2219M – Door Inner Barrier Materials
GM-3626M – Polyethylene Film
GMN-10031 – Thermoplastic Polyolefin – Recycled Rubber Modified
GMN-10044 – Performance Requirements for Exterior Plastic Parts with Paint Film
GMN-8351 – Energy Absorbing Countermeasures
GMP-PE-004 – Polyethylene High Density Copolymer Blow Molding Extrusion Grade Pellet Form
GMW-15702 – Plastic Molding Compounds
GMW-16456 – Polypropylene Copolymer – Mineral Filled, Heat Stabilized, Injection Molding
GMW-14171 – Heavy Layer Sound Barriers and Decoupler Assemblies
GMW-14194 – Fibrous Sound Absorption Materials
GMW-15473 – Flexible Expanded Rubber Materials for Air Dust Noise and Water Sealing
GMW-15523 – Door Inner Water Deflection Barrier Acoustic Material
GMW-15674 – Polypropylene Copolymer Mineral Filled Heat Resistant Weatherable Injection Molding
GMW-16597 – Carpet Materials for Non-Floor Applications
GMW-16803 – Non-Carpet Floor Covering Materials
GMW-3154 – Mandrel Bend Test
GMW-3205 – Determining Resistance to Odor Propagation of Interior Materials
GMW-3232 – Test Method for Determining the Flammability of Interior Trim Materials
GMW-4217 – Dimensional Stability

Honda Specifications

005A1-H8000-00 – Restricted Chemical Guidelines
HES C-206 – Flammability of Automobile Interior Materials
HES C252 – PP Resin Materials for Vehicles (Automobiles)

Hyundai Specifications

MS-361-10E – Fiber Board for Automotive

Mercedes Specifications

1455-001 – Non-Standard Material Construction
DBL-5972 – Single Layer Acoustic Insulating Materials
DBL-8585 – General Requirements Environmental Protection Hazardous Substances Dangerous Goods Negative Substance List for the selection of materials
VDA-270 – Determination of the odour characteristics of trim materials in motor vehicles
VDA-278 – Thermal Desorption Analysis of Organic Emissions for the Characterization of non-metallic materials for automobiles
WEB-V-100 – Laboratory Selection – Approved Labs

Nissan Specifications

NDS-80860NDS00-5 – Sealing Screen
NES-M-0301 – Substance Use Restrictions

Toyota Specifications

TIS-01204-00232-H – Part VOC Volume
TSK-5705G-C1 – Pressure Sensitive Adhesive Double Coated Tape for Exterior Parts
TSL-5705G – Covering Sheets for Dash Panel Inner Silencers
TSM-0500G – Flammability test method for interior non-metallic materials
TSM-0503G – Fogging Test Method for Non-Metallic Materials
TSM-0505G – Smell Quality of Non-Metallic Materials
TSM-0508G – Volatile Component Measurement method using sampling bag
TSM-1712G – Materials for Fuel Tank Cushion
TSM-5505G – Ethylene Vinyl Acetate Copolymer Resin Molding Material
TSM-5514G – Polypropylene Resin Molding Materials
TSM-5601G – Composite Reinforced Polypropylene Molding Materials
TSM-5608G-C2 – High Performance Polypropylene Resin Molding Material
TSZ-0001G – Control Method for Substances of Environmental Concern
TSZ-6005G – Indication Method of Material Marking for Plastic Parts and Rubber Parts